Aquarium & Tropical Fish Site
Tropical Fish Forums
Aquarium fishkeeping around the world!
 
ChatChat  HelpHelp   Search BoardSearch Board   MemberlistMemberlist   UsergroupsUsergroups 
 ProfileProfile   Check your private messagesCheck your private messages   Log inLog in   RegisterRegister 
DIY protein skimmer
Goto page 1, 2  Next
 Forum Index > Do It Yourself (DIY)  Reply to topic   Post new topic
Author Message
dale
Advisors


Joined: 10 Jan 2005
Location: Abbotsford Canada

PostPosted: 2006.11.06(Mon)2:56    Post subject: DIY protein skimmer Reply with quote

Here's a quick run through of a little skimmer I'm building for my temperate SW system. Apart from the needle wheel pump it cost about $75 to build and is comparable to a $1700 unit.

Here are the two main tools I'll use (always wear proper eye protection):

A "Dremel" type rotary tool with a cut off disc and a barrel sanding attachment to work the water bottle



and a compound mitre saw for cutting PVC piping



I begin by marking and cutting a 5G. water bottle.



This shot shows how I've cut at a spot that leaves an extended flange on the bottle


_________________
Intelligence is not having all the answers; it's knowing how to think!


Last edited by dale on 2006.11.06(Mon)4:03; edited 1 time in total
Back to top
View user's profile Send private message MSN Messenger
dale
Advisors


Joined: 10 Jan 2005
Location: Abbotsford Canada

PostPosted: 2006.11.06(Mon)3:23    Post subject: Reply with quote

Here's a shot of the Sedra 9000 needle wheel pump (off of the $1700 skimmer). I will be using the pump in a recirculating mode on the skimmer. It came with 1/2 of the unions glued in place and I couldn't find a reasonably priced replacement.



So I cut the collars off. Notice the 1/2" PVC pipe that fits snugly inside the pump lines.



I lined the intake and outlet of the pump up against the water bottle, marked, and then cut out holes for the bulkheads. I cut the rough holes with the cut off disc and smoothed things out with the sanding barrel.



Here are the installed bulkheads for the pump



and the pump assembly. Basically there are PVC reducers, pipes and 3/4" unions. At this point all the piping is dry fitted, not glued. Only after I'm satisfied with the final product will I will glue it all together.



Next I installed a bulkhead and fittings for the skimmer returnline (water out of skimmer).



And a bulkhead and fittings for the skimmer feed line (water into skimmer).



This is a view looking down at the guts of the skimmer. On the left there are the recirculating pumps feed and return bulkheads (the elbow at the bottom directs the return flow in a circular pattern). On the right is the skimmer feed and return bulkheads (again, the elbow directs the feed flow in a circular pattern).


_________________
Intelligence is not having all the answers; it's knowing how to think!


Last edited by dale on 2006.11.06(Mon)3:57; edited 1 time in total
Back to top
View user's profile Send private message MSN Messenger
dale
Advisors


Joined: 10 Jan 2005
Location: Abbotsford Canada

PostPosted: 2006.11.06(Mon)3:41    Post subject: Reply with quote

These next three shots show how the lid goes back on:

First I cut a little off the top to make it thinner than the base flange



It sits in place nicely



I am sealing it with silicone. I'm doing this in case I need to adjust something. Once I'm satisfied with the skimmers performance I can seal it permanently with marine Goop



Here is the skimmer return assembly. The gate valve allows me to adjust the water level in the skimmer.



I also cut the lip off the neck of the bottle so that 1 1/2" PVC would fit. The PVC is also secured for now with silicone.



The skimmer is fed with a small pump I had kicking around. I don't want too much flow through the skimmer so that the bubbles have more time to react with the organic matter.



And here's the skimming unit in a 50G. sump.



but all of this is a waste of time if one very important thing doesn't occur... The things gotta skim!
_________________
Intelligence is not having all the answers; it's knowing how to think!
Back to top
View user's profile Send private message MSN Messenger
dale
Advisors


Joined: 10 Jan 2005
Location: Abbotsford Canada

PostPosted: 2006.11.06(Mon)3:55    Post subject: Reply with quote

I have allowed the silicone to cure, filled my sump partially with saltwater and am now ready to take her out for sea trials.

I add some delicious skimmate from my coralife 125 superskimmer to the sump and mix it all around. This is about three days of dry skimmings worth.



Somethings happening!!!



This is what I have after 1 hour. It is a dark, dry skimmate.





After a bit I dumped the skimmate back into the sump and adjusted the gate valve to allow for a more wettish skimming flow.
This is after 1 hour of wet skimming.


_________________
Intelligence is not having all the answers; it's knowing how to think!
Back to top
View user's profile Send private message MSN Messenger
dale
Advisors


Joined: 10 Jan 2005
Location: Abbotsford Canada

PostPosted: 2006.11.06(Mon)4:02    Post subject: Reply with quote

Happiness is stinky smelly skimmer Very Happy

http://s106.photobucket.com/albums/m274/fisherder/?action=view&current=100_2573.flv
_________________
Intelligence is not having all the answers; it's knowing how to think!
Back to top
View user's profile Send private message MSN Messenger
McP
Advisors


Joined: 24 Jul 2004

PostPosted: 2006.11.06(Mon)10:11    Post subject: Reply with quote

Congrats on your success Dale! Its always nice to save some money Wink

If you had bought the needle wheel pump how much would this have cost in total? Approximately how many hours did the assembly take?
Back to top
View user's profile Send private message MSN Messenger
dale
Advisors


Joined: 10 Jan 2005
Location: Abbotsford Canada

PostPosted: 2006.11.06(Mon)13:57    Post subject: Reply with quote

Thanks McP.
I helped set up a SW tank for someone and received the pump as barter. New it's anywhere from $109 to $200.
Aside from the figuring and with all parts on hand it took only a couple of hours from start to finish.
_________________
Intelligence is not having all the answers; it's knowing how to think!
Back to top
View user's profile Send private message MSN Messenger
McP
Advisors


Joined: 24 Jul 2004

PostPosted: 2006.11.06(Mon)20:21    Post subject: Reply with quote

Looks like your DIY project is a reasonable deal even if you were to purchase a new pump. Good on ya Smile
Back to top
View user's profile Send private message MSN Messenger
Flame Angel
Regulars


Joined: 07 Nov 2006
Location: Sydney, Australia

PostPosted: 2006.11.12(Sun)2:19    Post subject: Reply with quote

Nice work, that's really impressive.
Did you design that by your self?
Back to top
View user's profile Send private message Send e-mail
Dusko
Moderators


Joined: 13 Feb 2006
Location: Denmark

PostPosted: 2006.11.12(Sun)4:53    Post subject: Reply with quote

Now this is worth a permanent article on Aquahobby, otherwise you are always welcome to publish it on my Aquarium Poetry Laughing Wink

I am impressed Dale!!!

I am planning in future time building a reef tank and my concern was the PRISE of the darn skimmer thing, but this sorts out the problem.

Thanks mate, you have a pint on me next time we meet Laughing

Kind regards, Dusko.
_________________
Back to top
View user's profile Send private message Visit poster's website
Display posts from previous:   
 Forum Index > Do It Yourself (DIY) All times are GMT - 6 Hours Reply to topic   Post new topic
Goto page 1, 2  Next
Jump to:  
  You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2008 phpBB Group

oF <=> oC in <=> cm G <=> L